INSTEON in-wall Relay Micro Module

Insteon
Special Price A$65.00 Regular Price A$89.00
Out of stock
SKU
IN2443-522

Add hidden on / off control of your appliance electrical outlets and lighting with this INSTEON Micro In-Wall Appliance module. Easily installed by a licensed electrician, its compact design means it will fit in the wall behind most lighting or electrical switches. Its clever design also means you still maintain local switch control as well as INSTEON control of the connected electrical load.

Categories: INSTEON

INSTEON In-wall Relay Micro Module

Micro-sized on/off INSTEON responder that adds control to a switched appliance or non-dimmable lighting zone. Installs behind a light switch.

Adding remote control to wired lights usually means replacing switches, not any more. With INSTEON's new dual-band micro-module relay, you can keep your existing antique, toggle or decorative wall switches while adding the customisable, remote control functionality that INSTEON offers.

This compact module installs behind your existing switch, giving it full INSTEON automation while retaining local control at the switch by way of sense wires. Connect the sense wires to any style wall switch to match any type of designer theme (antique, push-button, metal, etc.). The micro-module relay can also be installed as an in-line module within a fixture box, providing remote control without having to run wires to a wall switch.

Specifications

General

 
Product Name: INSTEON Inline Relay (On/Off) - Micro-Module
Product Code: 2443-522
Regions: Australia and New Zealand
In the box: INSTEON Inline Relay (On/Off) - Micro-Module
Warranty: 2 Years

INSTEON

 
INSTEON Powerline Mesh Repeater: Yes
INSTEON RF Mesh Repeater: Yes
INSTEON Controller: Yes
INSTEON Responder: Yes
Maximum links/scenes: 400
Status LED: Green / On, Red / Off, Blinks green or red during setup, Blinks red to indicate traffic (must be enabled via software)
LED brightness: Adjustable from off to 100% bright
Beep on button press: Beeps red to indicate traffic (must be enabled via software)
Local control: Yes
Commands supported as controller: On / Off, Fast On / Fast Off, Begin brighten / End brighten, Begin dim / End dim
Commands supported as responder: On / Off, Fast On / Fast Off, Beep
Software configurable: Yes
RF range: Up to 50 meters feet open air
Phase detect beacon: Yes
X10 support: Yes
X10 addresses: Any 1 of 256 (unassigned by default)
INSTEON device category: 0x02 Switched Lighting Control
INSTEON device subcategory: AUS / NZ (921.0 Mhz), 0x32

Mechanical

 
Mounting: Behind switch or outlet, or above light fixture in single-gang electrical box
Casing: UV stabalized plastic (INSTEON White)
Wire connections: Sense 1 (yellow): 24 AWG, 0.205mm², Sense 2 (purple): 24 AWG, 0.205mm²
Max. wire size: 4mm², 12 AWG (2.72mm diameter)
Min. cable size: 1.5mm², 15 AWG
Screw clamp connections: Line, Load 1, Load 1 (second terminal), Neutral
Set button: Yes
Beeper: Yes
Beep on button press: Optional (off by default)
LED: 1 RGB
Dimensions: 46.6mm W x 17.5mm H x 46.6mm D
Weight: 72g
Operating Conditions: Indoors, 0° C to 40° C, up to 90% relative humidity

Electrical

 
Voltage: 100VAC to 240VAC (± 10%)
Frequency: 50/60Hz auto-detected at power-up
Max. load: 10A, 3600W/240VAC resistive, 700W/240VAC inductive/capacitive, 2000W/240VAC bulbs/low voltage halogen
Load types: Resistive, Inductive/capacitive, Low voltage halogen
User replaceable fuse: N/A
Retain all settings without power: Yes, saved in non-volatile EEPROM
Standby power consumption: <1W
Safety approved: Approved for use in Australia and New Zealand
Certifications: AS/NZS 4268, CISPR 22, IEC 60669-2-1
You may also like!