INSTEON Relay DIN-Rail (on/off)

The INSTEON DIN Rail Appliance module clips directly onto a 35mm DIN rail and wires to load, power and neutral. Link it to an INSTEON keypad or any other INSTEON device for full remote control over the module and it's connected load.
INSTEON Relay DIN-Rail (On/Off)
Inline On/Off Responder that adds INSTEON control to a fixed on/off appliance or non-dimmable lighting zone.
The DIN Rail Dimmer module clips directly onto a 35mm DIN rail and wires to load, power and neutral. Link it to an INSTEON keypad or any other INSTEON device for full remote control over the module and it's connected load. Specifically, DIN Rail On/Off is compatible with the "Top hat rail EN50022" (sometimes referred to as a Type O or Type Ω) The DIN Rail On/Off will fit either variation of this style DIN rail (either 15 or 7.5 mm "high" off the mounting surface).
♦ Simply clip onto 35mm DIN rail and wire like any other INSTEON switch
♦ Optional sense wires allow for control via a connected, hard-wired switch
♦ Compatible with latching, single momentary and dual momentary switches
♦ Award-winning INSTEON technology provides superior reliability
♦ This product should be installed by a licensed electrician
What is a DIN rail?
A DIN rail is is simply a metal rail on which compatible products (circuit breakers, switches, etc.) can be snapped on to. Common electrical switch-boards and enclosures have a DIN rail behind the devices. The DIN rail can simply be mounted to any flat surface (or even across studs).
This product must be installed by a licensed electrical contractor.
General |
|
Product Name: | INSTEON Inline Relay (On/Off) - DIN |
Product Code: | 2453-522 |
Regions: | Australia and New Zealand |
In the box: | INSTEON Inline Relay (On/Off) - DIN |
Warranty: | 2 Years |
INSTEON |
|
INSTEON: | Controller and responder |
Maximum links/scenes: | 400 |
Status LED: | Green when load is on, red when load is off, Blinks green or red during setup, Blinks red once when responder does not acknowledge/blinks green once if all responders acknowledge (can be disabled via software) |
LED brightness: | Adjustable from off to 100% bright |
Local control: | Yes |
Commands supported as controller: | On / Off, Fast on / Fast off, Begin brighten / End brighten, Begin dim / End dim |
Commands supported as responder: | On / Off, Fast on / Fast off, Beep |
Software configurable: | Yes |
RF range: | 45m + |
Phase detect beacon: | Yes |
X10 support: | Yes |
X10 addresses: | Any 1 of 256 (unassigned by default) |
INSTEON device category: | 0x02 switched lighting control (all frequencies) |
INSTEON device subcategory: | 2453-222 (921MHz), 0x2E |
Operational |
|
Status LED: | Green. Blinks on activation |
Sense Modes: | Jumper Installed: Open = Group 1 On, Closed = Group 1 Off; Jumper Uninstalled: Open = Group 1 On (or off), Closed = Group 2 On (or Off) |
Aux. Sensor Input: | Senses contact closure |
Aux. Sensor Input Wire: | >= 20 gauge wire |
Setup Memory: | Non-volatile EEPROM |
Mechanical |
|
Mounting: | 35mm (top hat) DIN rail |
Max. cable size: | 4mm², 12 AWG (2.72mm diameter) |
Min. cable size: | 1.5mm², 15 AWG |
Screw DIN rail connections: | Line, Neutral, Load, Sense 1, Sense 2 |
Casing: | UV stabalized plastic (INSTEON White) |
Set button: | Yes |
Beeper: | Yes |
Beep on button press: | Optional (off by default) |
LED: | 1 RGB |
Dimensions: | 80mm W x 53mm H x 63mm D |
Weight: | 175g |
Operating Conditions: | Indoors, 0° C to 40° F, up to 85% relative humidity |
Electrical |
|
Voltage: | 100VAC to 240VAC |
Frequency: | 50/60Hz auto-detected at power-up |
Max. load: | 15A, 3600W/240VAC resistive, 700W/240VAC inductive/capacitive, 2000W/240VAC bulbs/low voltage halogen |
Load types: | Resistive, Inductive/capacitive, Low voltage halogen |
User replaceable fuse: | Yes (16 A (T)) 5x20mm fuse |
Retain all settings without power: | Yes, saved in non-volatile EEPROM |
Standby power consumption: | <1W |
Certification: | Approved for use in Australia and New Zealand |