INSTEON in-wall Motor Roller Shutter Controller Micro Module
Special Price A$45.00 Regular Price A$89.00
Out of stock
SKU
IN2444-522
Add hidden control of your home's motorised curtains, blinds or roller shutters with this INSTEON Micro In-Wall Motor module. Easily installed by a licensed electrician, its compact design means it will fit in the wall behind most electrical switches. Its clever design also means you still maintain local switch control as well as INSTEON control of the connected motorised device.
Categories: INSTEON
General |
|
| Product Name: | INSTEON Motor Controller - Micro-Module |
| Product Code: | 2444-522 |
| Regions: | Australia and New Zealand |
| In the box: | INSTEON Motor Controller - Micro-Module |
| Warranty: | 2 Years |
INSTEON |
|
| INSTEON Powerline Mesh Repeater: | Yes |
| INSTEON RF Mesh Repeater: | Yes |
| INSTEON Controller: | Yes |
| INSTEON Responder: | Yes |
| Maximum links/scenes: | 400 |
| Load brightness levels: | 32 locally (256 with software) |
| Status LED: | Green / On, Red / Off, Blinks green or red during setup, Blinks red to indicate traffic (must be enabled via software) |
| LED brightness: | Adjustable from off to 100% bright |
| Beep on button press: | Beeps red to indicate traffic (must be enabled via software) |
| Local control: | Yes |
| Commands supported as controller: | On / Off, Fast On / Fast Off, Begin brighten / End brighten, Begin dim / End dim |
| Commands supported as responder: | Open (On) / Close (Off), Begin raise (brighten) / / Begin lower (dim), End raise (brighten) / End lower (dim), Beep |
| Software configurable: | Yes |
| RF range: | Up to 50 meters feet open air |
| Phase detect beacon: | Yes |
| X10 support: | Yes |
| X10 addresses: | Any 1 of 256 (unassigned by default) |
| INSTEON device category: | 0x0E Window Coverings |
| INSTEON device subcategory: | AUS / NZ (921.0 Mhz), 0x32 |
Mechanical |
|
| Mounting: | Behind switch or outlet, or above light fixture in single-gang electrical box |
| Casing: | UV stabalized plastic (INSTEON White) |
| Wire connections: | Sense 1 (yellow): 24 AWG, 0.205mm², Sense 2 (purple): 24 AWG, 0.205mm² |
| Max. wire size: | 4mm², 12 AWG (2.72mm diameter) |
| Min. cable size: | 1.5mm², 15 AWG |
| Screw clamp connections: | Line, Load 1 (up), Load 2 (down), Neutral |
| Set button: | Yes |
| Beeper: | Yes |
| Beep on button press: | Optional (off by default) |
| LED: | 1 RGB |
| Dimensions: | 46.6mm W x 17.5mm H x 46.6mm D |
| Weight: | 72g |
| Operating Conditions: | Indoors, 0° C to 40° C, up to 90% relative humidity |
Electrical |
|
| Voltage: | 100VAC to 240VAC (± 10%) |
| Frequency: | 50/60Hz auto-detected at power-up |
| Max. load: | 8A resistive, 3A motor |
| Load types: | Resistive, Inductive/capacitive, Low voltage halogen, motor |
| Hardwired remote control: | Yes, either latching or momentary switches supported |
| User replaceable fuse: | N/A |
| Retain all settings without power: | Yes, saved in non-volatile EEPROM |
| Standby power consumption: | <1W |
| Safety approved: | Approved for use in Australia and New Zealand |
| Certifications: | AS/NZS 4268, CISPR 22, IEC 60669-2-1 |
You may also like!
