INSTEON in-wall Dimmer Micro Module

Add hidden dimmer control of your lighting with this INSTEON Micro In-Wall Dimmer module. Easily installed by a licensed electrician, its compact design means it will fit in the wall behind most lighting or electrical switches. Its clever design also means you still maintain local switch control as well as dimmable INSTEON control of the connected lighting.
General |
|
Product Name: | INSTEON Inline Dimmer - Micro-Module |
Product Code: | 2442-522 |
Regions: | Australia and New Zealand |
In the box: | INSTEON Inline Dimmer - Micro-Module |
Warranty: | 2 Years |
INSTEON |
|
INSTEON Powerline Mesh Repeater: | Yes |
INSTEON RF Mesh Repeater: | Yes |
INSTEON Controller: | Yes |
INSTEON Responder: | Yes |
Maximum links/scenes: | 400 |
Load brightness levels: | 32 locally (256 with software) |
Status LED: | Green / On, Red / Off, Blinks green or red during setup, Blinks red to indicate traffic (must be enabled via software) |
LED brightness: | Adjustable from off to 100% bright |
Local on-level: | Adjustable from 32 fixed brightness levels or resume dim |
Local ramp rate: | Adjustable from 0.1 second to 5 seconds locally (0.1 seconds to 9 minutes with software) |
Beep on button press: | Beeps red to indicate traffic (must be enabled via software) |
Local control: | Yes |
Commands supported as controller: | On / Off, Fast On / Fast Off, Begin brighten / End brighten, Begin dim / End dim |
Commands supported as responder: | On / Off, Fast On / Fast Off, Begin brighten / End brighten, Begin dim / End dim, Incremental brighten / Incremental dim, Beep |
Software configurable: | Yes |
RF range: | Up to 50 meters feet open air |
Phase detect beacon: | Yes |
X10 support: | Yes |
X10 addresses: | Any 1 of 256 (unassigned by default) |
INSTEON device category: | 0x01 dimmable lighting control |
INSTEON device subcategory: | AUS / NZ (921.0 Mhz), 0x39 |
Mechanical |
|
Mounting: | Behind switch or outlet, or above light fixture in single-gang electrical box |
Casing: | UV stabalized plastic (INSTEON White) |
Wire connections: | Sense 1 (yellow): 24 AWG, 0.205mm², Sense 2 (purple): 24 AWG, 0.205mm² |
Max. wire size: | 4mm², 12 AWG (2.72mm diameter) |
Min. cable size: | 1.5mm², 15 AWG |
Screw clamp connections: | Line, Load, Neutral 1, Neutral 2 |
Set button: | Yes |
Beeper: | Yes |
Beep on button press: | Optional (off by default) |
LED: | 1 RGB |
Dimensions: | 46.6mm W x 17.5mm H x 46.6mm D |
Weight: | 72g |
Operating Conditions: | Indoors, 0° C to 40° C, up to 90% relative humidity |
Electrical |
|
Voltage: | 100VAC to 240VAC (± 10%) |
Frequency: | 50/60Hz auto-detected at power-up |
Max. load: | 200W (at 240VAC) |
Load types: | Incandescent |
Hardwired remote control: | Yes, either latching or momentary switches supported |
User replaceable fuse: | N/A |
Retain all settings without power: | Yes, saved in non-volatile EEPROM |
Standby power consumption: | <1W |
Safety approved: | Approved for use in Australia and New Zealand |
Certifications: | AS/NZS 4268, CISPR 22, IEC 60669-2-1 |